Hubbardton-forge 101454 Instrukcja Użytkownika Pobierz pdf

Installation Instructions A15

For Chain Hanging Fixtures with Center Dish Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

14017 Rev A

To Install (Figure 1)

Component Parts

A Crossbar

B Nipple

C Nut

D Canopy Loop

E Canopy

F Loop Collar

G Chain

H Fixture Loop

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the crossbar (A) to the

electric box.

Note: A new electric box comes with screws. When replacing a fixture,

retain the existing screws for use with the new fixture.

3. Thread the nipple (B) into the crossbar and secure with lock nut (C); slide

canopy (E) over nipple and attach the canopy loop (D) to the nipple. Adjust

the nipple to proper length to ensure a snug canopy fit before proceeding.

4. Attach one end of the chain (G) to the fixture loop (H). Lace the wire

through every other link of the chain to the end. Slip wires and chain

through the loop collar (F) and canopy (E). Fasten the chain to the canopy

loop, and then slip the wires through the loop and nipple into the canopy

box. Make sure to provide enough slack in the wire to ensure the chain

supports the weight of the fixture.

5. Using suitable wire connectors (not provided) connect fixture wires to

supply wires (white to ribbed side of fixture’s cord, black to smooth side).

Connect all bare copper and/or green wires together and to the green

ground screw of the crossbar. Caution: Make sure wire connectors are

twisted on securely, and no bare wire is exposed.

6. Raise canopy to the ceiling and secure loop collar to canopy loop.

7. Install glass. (See instructions following)

8. Install light bulb(s) (not provided).

9. Restore electricity at main breaker.

Caution: This fixture has been designed with a small center dish allowing the

addition of a small decorative object of your choosing. To ensure that the

electric box can support the weight of the fixture and the added object, limit the

object’s weight to a maximum of ten pounds.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

e noted on fixture. Use onl

recommended bulbs with fixture.

(Figure 1)

1 2

14017 Rev A 1

Podsumowanie treści

Strona 1 - 14017 Rev A

Installation Instructions A15 For Chain Hanging Fixtures with Center Dish Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Bo

Strona 2

Installation Instructions A15 For Chain Hanging Fixtures with Center Dish Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Bo

Komentarze do niniejszej Instrukcji

Brak uwag

Hubbardton-forge 101454 Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Oświetlenie Hubbardton-forge 101454. Hubbardton Forge 101454 User Manual [en] Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Oświetlenie Hubbardton-forge 101454